Kilo Moana cruise from Honolulu to Tahiti. Operator: Guillaume Bourdin
20241024T1945: Cleaning
20241025T2100: Cleaning
20241026T2030: Cleaning
20241027T1852: Cleaning
20241028 at start up: Cleaning
20241029T2017: Cleaning
20241030T1814: Cleaning
20241030T2250: Before that datetime tower zero was 16° starboard of the boat heading. After that datetime the zero of the tower is set to the heading of the boat. Removed rust on the hypersas relay pin and changed dessicant.
20241031T1917: Cleaning
20241101T1932: Cleaning
20241102T1929: Cleaning
20241103T1942: Cleaning
20241104T2021: Cleaning
20241105T1909: Cleaning
20241106T1901: Cleaning
20241107T2130: Cleaning
20241108T1840: Cleaning (with isopropyl)
20241109T2051: Cleaning
20241110T2136: Cleaning
20241111T2058: Cleaning
20241112T1610: Cleaning
20241113T1907: Cleaning
20241114T2132: Cleaning
20241115T2138: Cleaning. Engine exhaust flying over Es sensor around 21:47, check data
20241116T2108: Cleaning
20241117T0727: Cleaning it was probably 19:27, not 07:27. This stupid laptop was set in AM/PM. Just changed that
20241118T: stopped storm
20241119T: stopped storm check file pySAS002_20241119_000000.raw, it was probably recording the deck
20241120T0109: Cleaning. Tower lost its zero. I had to turn the tower 41° portside and zero it to by aligned with the boat bow. I zeroed it a few times to prevent pulling the cable when it turned all the way.
20241121T0138: Cleaning. no heading, rust on the relay connector. Cleaned quickly but I will give it a good clean tahiti
20241123T0025: Cleaning. Tower lost zero, had to turn tower 74° to starboard to be aligned with boat heading. Tower zero-ed again once aligned with boat heading
20241123T2154: Cleaning
20241124T1957: Cleaning
20241125T2140: Cleaning
20241126T: Cleaning in port in Tahiti

Start cruise leg from Tahiti to Honolulu. Cleaning routine always pySAS, then Es, using Isopropyl. Operator: Ali Chase
20241128T: pysas not working, did trouble shooting all day. started working late afternoon local time.
20241129T1930: Cleaning. pysas working now, cleaned at 19:30UTC. re-set the zero; we powered down for cleaning instead of going to manual mode so it had to be re-set
20241130T1924: Cleaning, finshed pysas cleaning at 19:32. When first connected to pysas wifi, the instrument showed  manual mode (but files had been being saved). The tower would rotate with the manual tool,
but then it would go back to it's preferred position, almost like it was in both manual and auto mode at the same time. Toggled to auto mode and then back to manual mode, and then it worked. The zero position was still good. 
Files pySAS1129_191836.raw and pySAS002_20241129_191837.raw are nearly empty and probably junk and made during our trouble-shooting of the instrument on 11/29.
20241201T1916: Cleaning pySAS, then Es (remote connection to optics computer not working so Es sensor was logging during cleaning)
20241202T2115: Cleaning
20241203T1914: Cleaning
20241204T1919: Cleaning
20241205T1922: Cleaning

20241206T1916: Cleaning
20241207T1913: Cleaning
20241208T1917: Cleaning
20241209T1917: Cleaning
20241210T1915: Cleaning
20241211T: rainy/windy/no cleaning
20241212T1919: Cleaning, GPS was not working, unplugged and replugged both GPS at the yellow box, working now. Clock was still synced and zero heading was still good.
20241213T1918: Cleaning, GPS was off again - turned off sometime in the night. Unplugged and re-plugged and everything re-started. Clock was still synced and zero heading was maintained.
20241214T1924: Cleaning, GPS no time/no fix error - turned off and on repeatedly to get working again.
20241215T1914: Cleaning, GPS not working, replaced with spare units. Was working sporadically but then stayed when we removed metal clamps (?). 
turned off for packing up at 01:06 UTC 12/16