Digital Oceanographic Pressure Sensor
SBE 50

Print version     Current manual (older manuals)     Reference Sheet     Configuration options & accessories

• Pressure measurements at 16 Hz (16 samples/second).
• RS-232 serial interface, optional 0 - 5 volt output.
• No memory or batteries -- intended for use on vehicles that can supply power and acquire data.
• Depths to 7000 meters (titanium housing).
• Five-year limited warranty.

DESCRIPTION

The SBE 50 is a high-accuracy, high-resolution (16 Hz sampling) pressure sensor, intended for towed vehicle, ROV, AUV, or other autonomous profiling applications at depths up to 7000 meters (23,000 feet).

The SBE 50’s strain-gauge pressure sensor is offered in eight full scale ranges from 20 to 7000 dbars. Compensation of the temperature influence on pressure offset and scale is performed by the SBE 50’s CPU.

The SBE 50 is an easy-to-use, light, compact instrument ruggedly made of titanium and other low-maintenance (plastic) materials; it is well suited to even the smallest vehicle. Commands sent to the SBE 50 provide status display, data acquisition setup, and diagnostic tests. The SBE 50 must be externally powered, and its RS-232C data (and/or optional 0 - 5 volt output) logged or telemetered by the vehicle to which it is mounted. The SBE 50 does not support auxiliary sensor inputs.

SAMPLING MODES

The SBE 50 has two sampling modes:

• Autonomous sampling – The SBE 50 runs continuously and samples at sixteen scans per second (16 Hz). It can be set to average up to 255 samples, transmitting only the averaged data. The SBE 50 can be programmed to begin autonomous sampling when power is applied or on command.
• Polled sampling – On command, SBE 50 takes one sample and transmits the data.

The SBE 50 outputs:

• Raw pressure and pressure temperature values, or
• Data in ASCII engineering units (pressure in decibars or psia, or depth in meters or feet) – pressure is calculated using calibration coefficients stored in EEPROM; depth is calculated from pressure, based on user selection of salt or fresh water and user-input latitude.

The SBE 50 can be integrated with the SBE 32 Carousel Water Sampler and Auto Fire Module (AFM) to provide autonomous water sampler control for a system deployed on a non-conducting cable. The AFM supplies power to the SBE 50 and monitors the pressure transmitted by the SBE 50 in real-time, closing water sampler bottles at pre-defined pressures or depths, or whenever the system is stationary for a specified period of time.

The SBE 50 is supplied with:

• Titanium housing for depths to 7000 meters
• Strain-gauge pressure sensor
• XSG 4-pin I/O bulkhead connector
• MCBH Micro connector in lieu of XSG (optional)

The SBE 50’s optional Voltage Output interface provides 0 - 5 volt output proportional to the pressure or depth, in addition to the RS-232C output. When equipped with the Voltage Output Interface, the SBE 50 uses a 6-pin I/O bulkhead connector.

A Windows terminal program, Seaterm, is supplied for instrument setup, status display, and diagnostics.

Measurement Range: 0 to 20 / 100 / 350 / 600 / 1000 / 2000 / 3500 / 7000 meters (expressed in meters of deployment depth capability)

Initial Accuracy: ± 0.1% of full scale range

Typical Stability: 0.05% of full scale range per year

Resolution: 0.002% of full scale range
(D/A resolution for optional 0-5 volt output: 16 bit)

Power Requirements: 8 - 30 VDC

Housing Material: 3AL/2.5V Titanium

Depth Rating: 7000 meters (22,900 feet)

Weight:
In air  0.7 kg (1.5 lbs)
In water  0.4 kg (0.9 lbs)

ADDITIONAL INFORMATION / LINKS:

Documentation -- manual, photos, technical papers, application notes, etc.

• Current product manual (older manuals)
• Photo Gallery
• Print version of this specification sheet / brochure
• Application Notes:
  - 27Druck: (Druck) Strain Gauge Pressure Sensor Error Sources
  - 68: Using USB Ports to Communicate with Sea-Bird Instruments
  - 69: Conversion of Pressure to Depth
  - 71: Desiccant Use and Regeneration (drying)
  - 73: Using Instruments with Pressure Sensors at Elevations Above Sea Level
  - 84: Using Instruments with Druck Pressure Sensors in Muddy or Biologically Productive Environments

Sales Information -- options, accessories, cables, mount kits, spares, etc.

• Configuration options & accessories:
  - Details for SBE 50
  - Listing for all products
• Cables
• Spare parts

Software -- components of Seasoft V2

• Seaterm -- description, download
• SeatermAF -- description, download
• Seasave V7 -- description, download
• SBE Data Processing -- description, download

Links to Other Instruments of Interest

• Auto Fire Module (AFM) -- when used with SBE 50, allows SBE 32 Carousel Water Sampler to operate autonomously on non-conducting cables
• SBE 16plus V2 (serial interface) or 16plus-IM V2 SeaCAT C-T (P optional) Recorder (Inductive Modem interface) -- SBE 50 can be integrated via RS-232 bulkhead connector on Seacat to provide additional pressure data
• SBE 29 Strain-Gauge Pressure Sensor -- voltage output pressure sensor used as standard equipment on SBE 25 Sealogger CTD

Specifications are subject to change without notice.

Sea-Bird Home     Phone: (+1) 425-643-9866     E-mail: seabird@seabird.com