SBE 37-SIP-ODO MicroCAT C-T-ODO (Pressure optional) Sensor
Configuration Details

37-SIP-ODO MicroCAT includes:

• Serial Interface (RS-232 standard, RS-485 optional)
• Memory
• internal, integral Pump
• integrated Optical Dissolved Oxygen sensor

Note that 37-SIP-ODO does not include internal batteries. See 37-SMP-ODO for comparable instrument with internal batteries.

Pressure sensor is installed in end cap, & is not field replaceable / swappable. While highest pressure rating gives you most flexibility in using 37-SIP-ODO, it is at expense of accuracy & resolution. It is advantageous to use lowest range pressure sensor compatible with your intended maximum operating depth, because accuracy & resolution are proportional to pressure sensor's full scale range. For example, comparing 2000 & 7000 m sensors --

• 2000 m sensor:
  initial accuracy = 2 m (= 0.1% * 2000 m),
  resolution = 0.04 m (= 0.002% * 2000 m)
• 7000 m sensor:
  initial accuracy = 7 m (= 0.1% * 7000 m),
  resolution = 0.14 m (= 0.002% * 7000 m)

37-SMP-IDO shown; plastic housing detail similar for 37-SIP-ODO

Substituting plastic housing for standard 7000 m titanium housing provides lower cost option for shallow deployments.

37-SMP-IDO shown; clamp and guide detail identical for 37-SIP-ODO

Cable fits loosely through wire guide, & is clamped only at mounting clamp. See document 67219.

Thread for clamping to mooring cable:

• 37SIP-1b (1/4 in. diameter): 1/4-28 UNF
• 37SIP-1c (5/16 in. diameter): 5/16-24 UNF
• 37SIP-1d (3/8 in. diameter): 3/8-24 UNF
• 37SIP-1e (1/2 in. diameter): 9/16-12 UNC
• 37SIP-1f (6 mm diameter): 1/4-20 UNF
• 37SIP-1g (8 mm diameter): 5/16-24 UNF
• 37SIP-1h (10 mm diameter): 7/16 -14 UNF
• 37SIP-1i (12 mm diameter): 1/2-13 UNF
• 37SIP-1j (16 mm, 5/8 in. diameter): 5/8-18 UNF

Standard Connector (Impulse XSG)

Wet-pluggable Connector (MCBH)

Wet-pluggable connectors may be mated in wet conditions. Their pins do not need to be dried before mating. By design, water on connector pins is forced out as connector is mated. However, they must not be mated or un-mated while submerged. Wet-pluggable connectors have a non-conducting guide pin to assist pin alignment & require less force to mate, making them easier to mate reliably under dark or cold conditions, compared to our standard (Impulse XSG/RMG) connectors. Like standard connectors, wet-pluggables need proper lubrication & require care during use to avoid trapping water in sockets.

• Injection molded case with HPX resin plastic body, recessed wheels, automatic pressure equalization valve, hinged push-button latches, fold-down padded handle, & O-ring seal. Meets airline luggage regulations.
• Inner dimensions:
  29 x 18 x 10.5 inches (74 x 46 x 27 cm).
• Outer dimensions:
  31.3 x 20.4 x 12.2 inches (80 x 52 x 31 cm).

Price for 37SIP-6I reflects a credit for deletion of our standard wood crate.

801263 -- Some users prefer battery snap connector instead of red/black twisted wire leads. If 37SIP-5 (wet-pluggable connector) specified, order 801263 in place of 801206 if desired.

801385 -- Included with standard shipment; this is spare.

801206 -- Included with standard shipment if 37SIP-5 (wet-pluggable connector) specified; this is spare.

801378 -- Longer (20 m), shielded cable.

• Injection molded case with HPX resin plastic body, recessed wheels, automatic pressure equalization valve, hinged push-button latches, fold-down padded handle, & O-ring seal. Meets airline luggage regulations.
• Inner dimensions:
  29 x 18 x 10.5 inches (74 x 46 x 27 cm).
• Outer dimensions:
  31.3 x 20.4 x 12.2 inches (80 x 52 x 31 cm).